1、 SH -SH(NA)-080795ENG
[WIRING PRECAUTIONS] CAUTION Always ground the shielded cables for the programmable controller. There is a risk of electric shock or malfunction. For wiring and connection, properly press,
[WIRING PRECAUTIONS] CAUTION Always ground the shielded cables for the programmable controller. There is a risk of electric shock or malfunction. For wiring and connection, properly press,
2、 SH -SH(NA)-080726ENG
[WIRING PRECAUTIONS] CAUTION For wiring and connection, properly crimp or solder the connector with the tools specified by the manufactures and attach the connector to the module securely. Be
[WIRING PRECAUTIONS] CAUTION For wiring and connection, properly crimp or solder the connector with the tools specified by the manufactures and attach the connector to the module securely. Be
3、 SH -SH(NA)-080722ENG
A - 2 [WIRING PRECAUTIONS] CAUTION Always ground the shielded cables for the programmable controller. There is a risk of electric shock or malfunction. For wiring and connection, properly
A - 2 [WIRING PRECAUTIONS] CAUTION Always ground the shielded cables for the programmable controller. There is a risk of electric shock or malfunction. For wiring and connection, properly
4、 SH -SH(NA)-080708
危險 ● 應在可編程控制器的外部設置安全電路，當外部電源異常及可編程控制器設備故障時，能夠確保整個 系統(tǒng)的安全。 誤輸出、誤動作有可能導致發(fā)生事故。 (1) 應在可編程控制器的外部設置異常停止電路以及定位控制的上限 / 下限等的防止機械損壞的互鎖 電路等。 (2) 機械原點復歸控制通過原點復歸方向及原點復歸速度這 2個數據進行控制，通過定位夾具 ON開始 減速。如果設置了錯
危險 ● 應在可編程控制器的外部設置安全電路，當外部電源異常及可編程控制器設備故障時，能夠確保整個 系統(tǒng)的安全。 誤輸出、誤動作有可能導致發(fā)生事故。 (1) 應在可編程控制器的外部設置異常停止電路以及定位控制的上限 / 下限等的防止機械損壞的互鎖 電路等。 (2) 機械原點復歸控制通過原點復歸方向及原點復歸速度這 2個數據進行控制，通過定位夾具 ON開始 減速。如果設置了錯
5、 SH -SH(NA)-080699ENG
[DESIGN PRECAUTIONS] DANGER Do not write data into the "system area" of the buffer memory of intelligent function modules. Also, do not use any "prohibited to use" signals as an output signal t
[DESIGN PRECAUTIONS] DANGER Do not write data into the "system area" of the buffer memory of intelligent function modules. Also, do not use any "prohibited to use" signals as an output signal t
6、 SH -SH(NA)-080683ENG
Provide a safety circuit outside the programmable controller so that the entire system will opera safely even when an external power error or programmable controller failure occurs. Failure to
Provide a safety circuit outside the programmable controller so that the entire system will opera safely even when an external power error or programmable controller failure occurs. Failure to
7、 SH -SH(NA)-080648ENG
A - 1 [DESIGN PRECAUTION] DANGER Do not write data into the "system area" of the buffer memory of intelligent function modules. Also, do not use any "prohibited to use" signals as an out
A - 1 [DESIGN PRECAUTION] DANGER Do not write data into the "system area" of the buffer memory of intelligent function modules. Also, do not use any "prohibited to use" signals as an out
8、 SH -SH(NA)-080647ENG
[DESIGN PRECAUTION] DANGER Do not write data into the "system area" of the buffer memory of intelligent function modules. Also, do not use any "prohibited to use" signals as an output signa
[DESIGN PRECAUTION] DANGER Do not write data into the "system area" of the buffer memory of intelligent function modules. Also, do not use any "prohibited to use" signals as an output signa
9、 SH -SH(NA)-080647ENG
[DESIGN PRECAUTION] DANGER Do not write data into the "system area" of the buffer memory of intelligent function modules. Also, do not use any "prohibited to use" signals as an output signa
[DESIGN PRECAUTION] DANGER Do not write data into the "system area" of the buffer memory of intelligent function modules. Also, do not use any "prohibited to use" signals as an output signa
10、 SH -SH(NA)-080644ENG
Do not bunch the control wires or communication cables with the main circuit or power wires, or install them close to each other. They should be installed 100 mm (3.94 inch) or more from each o
Do not bunch the control wires or communication cables with the main circuit or power wires, or install them close to each other. They should be installed 100 mm (3.94 inch) or more from each o
11、 SH -SH(NA)-080578ENG
Be sure to tighten the screws using the specified torque. If the screws are loose, it may cause a short circuit, malfunctions or a drop of the module. Overtightening the screws may damage the
Be sure to tighten the screws using the specified torque. If the screws are loose, it may cause a short circuit, malfunctions or a drop of the module. Overtightening the screws may damage the
12、 SH -SH(NA)-080446ENG
controller, be sure to read the manual carefully and thoroughly confirm the safety. Especially in the above mentioned control operations that are performed from an external device to a remot
controller, be sure to read the manual carefully and thoroughly confirm the safety. Especially in the above mentioned control operations that are performed from an external device to a remot
Bulude 廣州凌控自動化科技有限公司 ◎版權所有
銷售熱線：020-28625769 傳真：020-28029239
