国产免费啪视频观看网站-国产免费区-国产免费全部免费观看-国产免费人成在线视频视频-国产免费爽爽视频免费可以看

廣州菱控|三菱
當前位置:首頁 >> 資料下載 >> 三菱 >> 變頻器 >> 三菱 M700V 三菱-M700V 系列 HANDBOOK
三菱 M700V 三菱-M700V 系列 HANDBOOK
所屬類別:三菱 >> 變頻器
資料介紹:

M01 Dog overrun 0001
Details When returning to the reference position, the near-point detection limit switch did not stop over
the dog, but overran the dog.
Remedy - Increase the length of the near-point dog.
- Reduce the reference position return speed.
M01 Some ax does not pass Z phase 0002
Details One of the axes did not pass the Z-phase during the initial reference position return after the
power was turned ON.
Remedy - Move the detector one rotation or more in the opposite direction of the reference position,
and repeat reference position return.
M01 R-pnt direction illegal 0003
Details When manually returning to the reference position, the return direction differs from the axis
movement direction selected with the AXIS SELECTION key.
Remedy - The selection of the AXIS SELECTION key's +/- direction is incorrect. The error is canceled
by feeding the axis in the correct direction.
M01 External interlock axis exists 0004
Details The external interlock function has activated (the input signal is "OFF") and one of the axes
has entered the interlock state.
Remedy - As the interlock function has activated, release it before resuming operation.
- Correct the sequence on the machine side.
- Check for any broken wires in the "interlock" signal line.
M01 Internal interlock axis exists 0005
Details The internal interlock state has been entered.
The absolute position detector axis has been removed.
A command for the manual/automatic simultaneous valid axis was issued from the automatic
mode.
The manual speed command was issued while the "tool length measurement 1" signal is ON.
Remedy - The servo OFF function is valid, so release it first.
- An axis that can be removed has been issued, so perform the correct operations.
- The command is issued in the same direction as the direction where manual skip turned ON,
so perform the correct operations.
- During the manual/automatic simultaneous mode, the axis commanded in the automatic
mode became the manual operation axis. Turn OFF the "manual/automatic valid" signal for
the commanded axis.
- Turn ON the power again, and perform absolute position initialization.
- Turn OFF the "tool length measurement 1" signal to start the program by the manual speed
command.
M01 H/W stroke end axis exists 0006
Details The stroke end function has activated (the input signal is "OFF") and one of the axes is in the
stroke end status.
Remedy - Move the machine manually.
- Check for any broken wires in the "stroke end" signal line.
- Check for any limit switch failure.
M01 S/W stroke end axis exists 0007
Details The stored stroke limit I, II, IIB or IB function has activated.
Remedy - Move the machine manually.
- Correct any setting error of the parameters for the stored stroke limit.
立即下載     
相關下載
主站蜘蛛池模板: 2019国内精品久久久久久 | 婷婷亚洲综合一区二区 | 亚洲欧美二区三区久本道 | 97超精品视频在线观看 | 91精品国产乱码久久久久久 | 精品视频自拍 | 亚洲春色在线视频 | 毛片免费看牛牛影视 | 九九久久国产精品 | 一级做a爱片特黄在线观看免费看 | 一节毛片 | 国产一区二区视频在线观看 | 国产无遮挡又黄又爽在线视频 | 日韩一级一欧美一级国产 | 福利亚洲| 99欧美精品| 欧美黄色一级 | 久久er热在这里只有精品66 | 婷婷综合色 | 久久久国产视频 | 一级毛片卡 | 婷婷六月久久综合丁香可观看 | 色网站在线免费观看 | 嗯啊在线观看免费影院 | 欧美亚洲综合视频 | 最近更新中文字幕3 | 91原创视频在线 | 亚洲精品在线影院 | 免费一级大片儿 | 国产精品永久免费 | 国产精品探花千人斩久久 | 美国一级做a一级视频 | 成人国内精品久久久久影院 | 综合啪啪 | 黄黄影院 | 婷婷久久激情综合啪啪 | 亚洲国产日韩在线成人蜜芽 | 中国免费一级毛片 | 国产日韩欧美在线 | 一区二区三区四区在线视频 | 日韩欧美a级高清毛片 |